Fast curing adhesive Teknofay Rapid C1FT(Текнофей Рапид C1FT)

Products > Glue and grout for tiles

Fast curing adhesive Teknofay Rapid C1FT(Текнофей Рапид C1FT)

Fast curing, highly effective, elastic cement-based adhesive with reduced vertical sliding

858
uah
x
bag
=
858 uah
CHECKOUT

Введите свои данные

Teknofay Rapid C1FT is a fast curing highly effective elastic cement-based adhesive with reduced vertical sliding.

Application areas:

  • For laying materials on concrete surfaces, plaster, drywall, aerated concrete
  • For laying ceramics, granite, natural stone, etc.
  • For objects that need to be put into operation during the day

Properties of adhesive:

  • Fast curing (during 6 hours)
  • Holding on to vertical surfaces
  • Easy to use
  • Waterproof
  • Grouting of joints is possible after 3-4 hours after uusing adhesive
Colour Grey
Expiration date 12 months
Packaging 25 kg bag
Application temperature +5 °C - +35 °C
The ratio of the components of the compound 6-7,5 liters of water / 25 kg of powder
The life time of the compound 30 minutes
Thermal stability -40°C - +80°C
Resistance to moving out ≤ 0,5 mm
Ready for grouting joints 3-4 hours
Commissioning after 6 hours > 0,5 N/mm2
After soaking ≥ 1,0 N/mm2
After soaking in a humid environment ≥ 1,0 N/mm2
After soakding at high temperatures ≥ 1,0 N/mm2
Freeze–Thaw cycles ≥ 1,0 N/mm2

Consumption table:

Teknofay Rapid C1FT Compound density (g/l) Consumption of powder (kg) Volume of water for mixing (l)
25 kg craft bag 1,7 3-5 6-7,5
  • Before applying the material, clean the surface from any types of oil, rust, detergents, dirt and other substances that prevent setting.
  • If there are cracks or cavities on the surface – they must be sealed with Teknorep.
  • When laying tiles on a marble or ceramic surface, you should give it some roughness.
  • When laying tiles on a concrete surface, it should be moistened.
  • Pour 6-7,5 liters of clean water into a clean container. Slowly pour the Teknofay Rapid powder (25 kg) into a container with water and use a low-speed mixer to knead the composition for 5 minutes until a homogeneous mass is obtained. Leave the compound for 3 minutes, then re-mix it with a mixer for 2 minutes.

Notes:

  • The work should be carried out at an air temperature of +5 to +35 °C. When laying tiles at a low (below +5 °C) or elevated (above +35 °C) temperature, it is necessary to cover the newly laid tile with a thermal insulation material.
  • The grout should be applied no earlier than 4 hours after laying the tile.
  • After applying the compound, it is necessary to protect the surface from adverse weather conditions, such as direct sunlight, strong wind, high air temperature (more than +35 °C), rain and frost.
  • The tools and equipment used must be washed with warm water immediately after use. You should also thoroughly wash your hands and face with warm water and soap.
  • The product may cause irritation if it gets on the skin. It is necessary to use work clothes, protective gloves, a mask and glasses. Before starting work, you can also apply a protective cream on your hands. In case of contact with the eyes, immediately rinse the eyes with warm water and consult a doctor.

Storage rules:

  • Store in a dry, frost-proof place, in an undamaged original packaging.

1. What to add to the tile adhesive for quick drying?

On the Internet, you can find various tips on additives in glue for faster drying, but, at the same time, no one can guarantee the quality of laying. It is much better to use a special fast-hardening adhesive compound, for example, Teknofay Rapid C1FT, thanks to which the finishing material will not only be qualitatively and reliably glued, but also commissioning will be possible after 6 hours. 

2. How to speed up the drying of the glue?

On average, tile glue dries after 24 hours and, unfortunately, it is impossible to speed up this process, except to make the thinnest possible thickness of the adhesive layer. This can only be done when laying small-sized light tiles.
But there are special fast-hardening adhesives that are a little more expensive than conventional tile glue, but also dry 4 times faster. 

3. Which tile adhesive is quick-drying?

Teknofay Rapid C1FT is a fast-hardening, highly effective elastic cement-based adhesive solution. When using Teknofay Rapid C1FT, the seams can be rubbed after 3-4 hours, and commissioning is possible in an average of 6 hours.

4. How long does the tile adhesive dry?

On average, tile adhesive dries in 24 hours, there are adhesive compositions that dry up to 36 hours, but there are also quick-drying compositions, thanks to which the surface will be ready for operation in 6 hours.

5. How to stir the tile glue manually?

Unfortunately, to obtain a homogeneous consistency of tile glue, it is impossible to do without using a special mixer. With it, you can quickly and conveniently mix dry powder with water in a matter of minutes. It is almost impossible to achieve such a result manually.  

Product publications

Where should I start laying tiles?
Where should I start laying tiles?

Laying decorative material on the floor usually begins with the far corner (far entrance) of the surface, which we see immediately as we enter the room.

Read article
Useful tips for laying tiles
Useful tips for laying tiles

If you need to put the surface into operation very urgently, then you should use a special tile adhesive, with which you can rub the seams after 3-4 hours. For example, Teknofay Rapid.

Read article
Laying wall tiles in the bathroom with your own hands
Laying wall tiles in the bathroom with your own hands

The tile, like other decorative material, must be laid on a flat surface.

Read article
Types of tile adhesives and their features
Types of tile adhesives and their features

The most popular and widely used tile adhesive compositions are cement

Read article
Quick Action Tile Adhesive
Quick Action Tile Adhesive

Quick-acting tile adhesive is indispensable where it is urgently necessary to finish repair and construction work and put the facility into operation within a day

Read article
How to speed up the setting time of tile glue
How to speed up the setting time of tile glue

If the setting time of the glue is very important to you, we recommend choosing a fast-hardening glue - Teknofay Rapid C1FT immediately, with its help the finishing material will be ready for operation in 6 hours.

Read article