21 Jul 2023
How to attach OSB to concrete?
Chemical anchors or glue can be used for a stronger fix
Read articleChemical Anchor Teknobond 400 S(Текнобонд 400 S)
Two component fast-curing thixotropic chemical anchor
270 uah
x
pc.
=
270 uah
Teknobond 400 S is a two-component fast-curning thixotropic chemical anchor based on synthetic epoxy acrylate resin.
Application areas:
- For the installation of fittings and connecting rods in concrete, hollow and solid brick
- For anchor bolts and pins
- For installation of pipes and plumbing in central heating, ventilation, etc.
- For fixing injection packers
- For gluing all types of building materials
Properties of chemical anchor:
- Quick-hardening
- Easy to use
- Pasty
- Does not slip off any kind of surfaces
- Prevents the development of reinforcement corrosion
- It has a high resistance to chemicals
| Packaging | 410 ml cartridge |
| Expiration date | 12 months in the closed original packaging |
| The life time of the compound | 7-10 minutes (at a temperature of 20 °C) |
| Complete drying | 7 days |
| Re-application time | 1 hour (at a temperature of 20 °C) |
| Application temperature | 0 °C - + 80 °C |
| Pressure strength | 60-70 N/mm2 |
| Adhesion (to the concrete surface) | > 4 N/mm2 |
| Flexural strength | 18-20 N/mm2 |
| Tear-out strength | ≤ 0,6 mm (under 75 kN load) |
| Tensile strength | ≤ 0,6 mm (under 50 kN load after 3 months) |
| Standard | In accordance with TS EN 1504-6 |
- Before applying the material, clean the surface from any types of oil, rust, detergents, dirt and other substances that prevent setting by using compressed air.
- Concrete bases must be clean, strong and have sufficient adhesion.
- Using a puncher, you should drill a hole of the required diameter and depth. The diameter and depth of the hole must correspond to the size of the anchor element used. The hole should be cleaned with a round wire brush and compressed air from dust and dirt. Then squeeze the trigger and hold it until the two separate components of the cartridge together come out of the tip of the static mixer. Slowly pull out the cartridge, filling the hole. Make sure that there are no air gaps inside.
- An extension cord can be used in deep holes. When inserting the anchor, it is necessary to scroll it. Next, an anchor element should be placed in the hole. The anchor element must not be moved or loaded during curing.
- To open the lid, turn it. Then install the tip of the static mixer. Place the cartridge in the gun and start applying.
- If the application process is stopped, the tip of the static mixer can be left on the cartridge after the pressure is released.
- If the resin has hardened in the static mixer, a new insert must be installed before starting work.
Notes:
- Use anchor dowels to fix the anchor material to hollow materials (bricks or blocks).
- When storing an open cartridge, remove the static mixer, wipe the cartridge neck with a clean, dry cloth and close the lid.
- Contains styrene.
- Combustible.
- Harmful to health if inhaled
- The product may cause irritation in contact with the skin and eyes. It is necessary to use work clothes, protective gloves, a mask and glasses. In case of contact with the eyes, immediately rinse the eyes with warm water and consult a doctor.
- Keep out of reach of children
- Use in well-ventilated areas
- The tools and equipment used must be cleaned immediately after use.
Product publications
29 Aug 2022
Disadvantages of chemical anchors. Is it worth giving preference to chemical anchors instead of mechanical ones?
Today, there are no analogues of chemical anchors, especially when it is necessary to attach a heavy element to a hollow base. Despite this, the material still has several disadvantages.
Read article
26 Aug 2022
Fasteners for high loads. What to choose a chemical or mechanical anchor?
A mechanical anchor will not be able to cope with fastening into weak bases. These include hollow blocks and bricks with voids. But a chemical anchor is ideal for working on such bases.
Read article
