Tenax Profflex B one-component acrylic sealant for interior use 7 kg, White
PROFFLEX B - one-component acrylate sealant with high vapor barrier properties. The sealant is intended for performing the inner layer of the assembly joint in accordance with DSTU-N B V.2.6-146:2010, with an allowable deformation of the assembly joint of no more than 15%, for sealing the inner contour of window, door and balcony structures.
1485 uah
PROFFLEX B - one-component acrylate sealant with high vapor barrier properties. The sealant is intended for performing the inner layer of the assembly joint in accordance with DSTU-N B V.2.6-146:2010, with an allowable deformation of the assembly joint of no more than 15%, for sealing the inner contour of window, door and balcony structures.
PROPERTIES
-
High vapor barrier properties
-
Very good adhesion to most building materials
-
Protects against water vapor penetration from living spaces into the installation joint
-
Ready to use
-
Resistance to deformation
-
Durability
-
Possibility of use at sub-zero temperatures
-
Surface coloring possible
-
Due to its high thixotropy, the sealant can be applied to horizontal, vertical and inclined surfaces.
-
Appearance - paste
AREAS OF APPLICATION
The sealant is completely ready for use.
We also recommend using Profflex A acrylate sealant for the outer mounting layer.
At low temperatures, the viscosity of the sealant increases, so before use, we recommend keeping the sealant in a heated room for at least 24 hours. The recommended temperature of the sealant for application is +5 ° C to 35 ° C (minimum to -13 ° C).
TECHNICAL SPECIFICATIONS
| Parameters | Value |
| Consistence | Thixotropic paste |
| Basis | Polyacrylate |
| Hardening | Water evaporation |
| Vapor permeability resistance, (m2·h·Pa)/mg, not less | 2.5 |
| Surface film formation time, h. |
1 hour (at + 23°C and normal humidity) * |
|
Curing time at a layer thickness of 3 mm |
48 hours (at + 23°C and normal humidity) * |
|
Density, not less than kg/m3 |
1592 kg/m3 |
|
Recommended application temperature range |
From +5 °C to 35 °C, (minimum ambient temperature for application up to -20 °C and relative humidity not more than 90%). Minimum product temperature for application -13 °C |
|
Operating temperature range |
From - 400C to + 800C |
|
Adhesive strength, MPa, not less than: -PVC -tree, -metal, -concrete |
0.55 0.83 0.61 0.88 |
|
Flow resistance, mm per 2 mm of thickness, no more |
0 |
|
Bond strength limit, MPa, not less |
0.8 |
|
Resistance to deformation, %, not less |
15 |
|
Elongation at break % |
not less than 260% |
| Color |
white |
|
Freeze/thaw stability |
10 cycles |
|
Projected service life in conditional years, not less |
20 |
*With a decrease in temperature or an increase in humidity, the time increases.
SAFETY AND PRECAUTIONS
Keep out of reach of children. Avoid contact with unprotected skin and eyes. Do not take internally. When working, use protective equipment: gloves, overalls, eye and face protection. In case of contact with skin or eyes, rinse with plenty of warm water.
STORAGE AND TRANSPORTATION
The warranty shelf life is 12 months at a temperature of - 5 ° C to + 35 ° C in intact factory packaging. Transportation and storage at a temperature of up to - 20 ° C is allowed, while the total storage time at sub-zero temperatures should not exceed 15 days, and the number of freeze/thaw cycles should not exceed 10.
Preparation: The sealant is completely ready for use. Before application, degrease the surface, clean it of dirt, dust, loose particles. The edges and surfaces of the openings should not have chips, sinks, concrete mortar influxes and other damage with a height (depth) of more than 10 mm. Defective areas should be filled with waterproof mixtures. Loose, crumbling areas of the opening surfaces should be strengthened (treated with binding mixtures or special film materials. It is possible to apply the sealant to a dry and wet surface. The presence of dripping moisture on the surface is unacceptable. When working in winter, clean the surface from snow, ice and frost. It is unacceptable to apply the sealant during precipitation (rain and snow).
Application: The sealant is applied to the prepared surface using a spatula or paint brush. The recommended layer thickness is from 3.5 to 5.5 mm. The ambient temperature when applying the sealant is from -20 ° C to 35 ° C and the relative humidity is not more than 90%. When applying the sealant, it is recommended to protect the front edges of the structures with masking tape to prevent their contamination. The masking tape must be removed before the sealant forms a surface film.
Finishing and cleaning of the tool: Fresh sealant is washed off with warm water. Polymerized sealant is removed mechanically.
