Repair compound Teknorep 200(Текнореп 200)

Products > Repair compound for concrete

Repair compound Teknorep 200(Текнореп 200)

One component thin-layer repair compound reinforced with polymer fibers.

780 uah

Введите свои данные

Teknorep 200 is an one component thin-layer cement-based repair compound reinforced with polymer fibers.

Scope of application:

  • To fill in irregularities after removing the formwork
  • For the repair of prefabricated reinforced concrete elements
  • For repair of damages and cracks on any mineral surfaces
  • For repairing damages and cracks in engineering structures, such as metro, highways, dams
  • To obtain a smoother surface during minor repairs

Properties of concrete repair material:

  • Easy to use
  • It is resistant to freezing and thawing
  • Does not cause corrosion
  • Non-toxic
Colour Grey
Expiration date 12 months in a dry environment in a closed package
Packaging 25 kg bag
Application temperature +5 °C - +35 °C
Mixing ratio 4-5 liters of water / 25 kg of powder
Life time of the compound ≥ 45 minutes
Consumption of the compound 1.9 kg/m2
Granule size  0.700 mm
Commissioning 24 hours
Thickness of application 3-30 mm
Bending strength (EN 12808-3) > 7.0 N/mm2
Adhesion strength to concrete (EN 1542) > 1.0 N/mm2
Compressive strength (EN 12808-3) > 25 N/mm2
Shrinkage (EN 12617-4) > 0.8 N/mm2
Capillary absorption of water (EN 13057) < 0.5 kg/m2*h
Fire resistance A1

Consumption table:

Teknorep 200 Compound density (kg/l) Consumption of powder per 1 mm/1 m2 (kg)  Volume of water for mixing (l)
25 kg kraft bag 2,05 1,9 4 - 5
  • Before applying the material, the surface should be cleaned of any types of oil, rust, detergents, dirt and other substances that prevent setting.
  • If it is necessary to prime the surface, you should use the Tekno AD primer and then use the Teknorep 200 repair compound.
  • To prepare the working solution, pour 4.0-5.0 liters of clean water into a clean container. Pour the Teknorep 200 powder (25 kg) into a container with water and use a low-speed mixer (400-500 rpm) to knead the composition for at least 5 minutes until a homogeneous mass is obtained. Leave the resulting compound for 3 minutes, then re-mix the compound for 2 minutes.
  • Do not add water to the already mixed compound.


  • For outdoor use, in the first 3 hours of solidification of the compound, it is necessary to protect the surface from moisture, sunlight and frost.
  • When used at a low temperature, the lifetime of the compound increases, at an elevated temperature it decreases.
  • Work should be carried out in compliance with safety and hygiene standards, using a mask and glasses.
  • To obtain a smooth surface, apply the compound with a spatula. If necessary, apply a layer with a thickness of more than 30 mm, you should perform the work in several layers.
  • The freshly applied solution must be protected from adverse weather conditions, such as direct sunlight, high temperatures < + 35 °С, precipitation and frost.
  • The tools and equipment used must be washed immediately after use.

Product publications

How to seal the holes after removing the formwork in concrete
How to seal the holes after removing the formwork in concrete

Teknorep 200 is a cement—based repair thin-layer mixture reinforced with polymer fibers, suitable for filling voids left after removing the formwork during the construction of concrete structures.

Read article
What kind of repairman to fix a crack in the wall
What kind of repairman to fix a crack in the wall

Teknorep 200 is a repair thin layer mixture with a density of 2.05 kg/l, reinforced with polymer fibers, and is used for repairing any mineral surfaces, sealing cracks in engineering structures as highways, dams, mines.

Read article