Plaster Teknoizosiva (Текноизосыва)

• Before applying the material, clean the surface from any types of oil, rust, detergents, dirt and other substances that prevent setting.
• If there are cracks or cavities on the surface – they must be sealed with Teknorep.
• The gaps between the thermal insulation boards should be filled with small pieces cut from the same material.
• Before plastering, you should make holes for dowels on the slabs with a punch. Depending on the thickness of concrete, bricks, aerated concrete or thermal insulation board, the appropriate size of the dowel should be chosen. At least 6 dowels should be installed on 1 m². The higher the floor, the more dowels need to be installed.
• If the dowel is too protruding or vice versa-too deeply clogged, then after rain or direct sunlight it will become visible and the appearance of the surface will be spoiled.
• After finishing the work with the dowels, you can start plastering. Teknoizosiva is applied to the thermal insulation boards, on which the installation of dowels has been completed, using a 10x10 mm serrated steel spatula.
• Pour 6-7 liters of clean water into a clean container. Pour the dry Teknoizosiva compound (25 kg) into a container with water and use a low-speed mixer to knead the composition for at least 5 minutes until a homogeneous mass is obtained. Leave the resulting mixture for 3 minutes, then re-mix it with a mixer for 2 minutes.
• Places with sharp changes in the cross-section, such as doors and windows, should be reinforced with a grid for plaster. It is also recommended to use mesh corner profiles on the corners of buildings to achieve a perfectly smooth surface.
• The work should be carried out at an air temperature of +5 to +30 °C.

Notes:

• Do not use Teknoizosiva in strong wind, rain or in direct sunlight.
• After plastering, it is necessary to protect the surface from adverse weather conditions, such as direct sunlight, strong wind, rain and frost.
• If the ambient temperature is above +25 °C, it is necessary to moisten the surface with a water spray.
• Decorative plaster can be applied 24 hours after application in the summer and 48 hours after application in the winter.
• The product may cause irritation if it gets on the skin. It is necessary to use work clothes, protective gloves, a mask and glasses. Before starting work, you can also apply a protective cream on your hands. In case of contact with the eyes, immediately rinse the eyes with warm water and consult a doctor.

1. What is the best plaster?

One of the best plasters is considered elastic plaster Teknoizosiva on a cement basis. The material has a wide scope of application and a competitive price in the Ukrainian market.

2. What is the difference between plaster and putty?

Both plaster and putty are building mixes that are used to level and harden surfaces. More visible irregularities or cracks are sealed with plaster. Also, the difference is that after applying the putty, the surface will be perfectly smooth and after applying the plaster – smooth, but rough.

3. How do they plaster the walls in the apartment?

When choosing construction and repair materials for residential premises, pay attention to their environmental friendliness. For plastering the walls in the apartment, it is recommended to use Teknoizosiva on a cement basis. Plaster is not fastidious in work and is suitable for surface finishing both inside and outside the premises.

4. Which plaster manufacturer should I choose?

In accordance with the price and quality indicators, we recommend paying attention to the best Turkish manufacturer of plant chemistry materials, including Tekno plaster.

6. Is it possible to immediately putty the walls without plaster?

If the surface is perfectly smooth, then the application of plaster is not a mandatory stage of repair work. But if there are small cracks or irregularities on the surface, it is recommended to plaster the surface in 2 layers, then proceed to putty. 

7. Is it possible to use plaster instead of putty?

Plaster and putty are similar in composition, but the resulting effect is different. Therefore, if you want to get smooth, even surfaces, then use putty, since after plastering the walls will have some roughness. But if the surface is a little uneven, then first you need to apply plaster in several layers, after which you can proceed to putty. 

8. What kind of plaster for outdoor work?

Plaster intended for outdoor work must be resistant to all weather conditions. This is exactly what Teknoizosiva cement-based plaster is.