Hardener for printed concrete based on quartz fillers and arc additives to increase the wear resistance of the surface
Teknoser Baski is a hardener for freshly laid printed concrete based on quartz fillers and other additives to increase the wear resistance of the surface.
Application
Teknoser Baski is applied to the surface of freshly laid concrete. It is mainly used on terraces and balconies, in offices and bars, in galleries and homesteads, in courtyards and by swimming pools, in underground passages and at metro stations.
Features / Advantages
| Colour | In various colors |
| Expiration date | 12 months in a dry environment in a closed package |
| Packaging | 25 kg bag |
| Expenditure | 3-5 kg/m2 |
| Application temperature | + 5 °C - + 30 °C |
| Life time of the compound | 4 hours (+ 20°C) |
| Flexural strength | ≥ 7 N/mm2 |
| Compressive strength | ≥ 50 N/mm2 |
| Abrasion resistance (according to the Boehme method) | ≤ 5,5 cm3/50 cm2 |
| Fire resistance | A1 |
Foundation quality / preliminary preparation
High-quality concrete mix should be used, which must meet the requirements of local standards. The characteristics of concrete are determined by its class, established by its static calculation and general recommendations for the design of concrete mixtures. The water-cement ratio should not be too low, since a certain amount of water is necessary for the hydration of Teknoser Baski. To reduce the likelihood of shrinkage cracks, it is recommended to use Teknoflow Super plasticizer.
When choosing supplements, be sure to consult with Tekno specialists.
After pouring concrete, the surface should be leveled with vibrators to strengthen and level the concrete surface.
Application
On the prepared concrete surface, you should gradually sprinkle Teknoser Baski with a consumption of 3-5 kg / m2, wait about 10 minutes and rub it with special ironers, paying special attention to the processing of the edges. It is not recommended to apply Teknoser Baski on light surfaces (white, yellow). Next, apply a separator for Teknoser Ayrac printing plates and start the printing process. After 1-2 days, the surface should be well rinsed with pressurized water.
Limitations
1. What is needed for printed concrete?
To work with printed concrete, you will need: concrete mix, formwork, vibrating screed, squeegee, grease for printing plates and printing plates.
2. What is sprinkled on printed concrete?
To create printed concrete, the freshly laid concrete compound is sprinkled with a hardener, for example, Teknoser Baski, which is made on the basis of quartz fillers and other special additives that increase the wear resistance of the surface.
3. Which is cheaper printed concrete or paving slabs?
Comparing printed concrete with pavement tiles of average quality - the price will be approximately the same. But if you want to make a more interesting pattern or use high-quality paving slabs, printed concrete will be much cheaper.
4. How much does a square meter of printed concrete cost?
The cost per square meter of printed concrete when using the Teknoser Baski hardener is about 38 UAH (excluding the concrete compound itself and the disconnector for printing plates). The cost of 1 m2, taking into account the hardener Teknoser Baski and the Tekno Ayrac disconnector, is about 66 UAH (also excluding the concrete compound itself).
5. What is decorative printed concrete?
Decorative printed concrete is one of the varieties of horizontal surface cladding with which you can create a very beautiful surface for natural stone, paving stones or tiles, which, in addition to a beautiful appearance, increases the strength and wear resistance of concrete.
6. What is a concrete fixer?
Concrete binder is used to increase the wear resistance of the surface. For sidewalks, exhibition and shopping centers, for underground passages and metro stations, for hangars and mechanical repair shops, for parking lots, garages and ramps.
With the correct execution of all stages of creating a decorative coating using high-quality materials, printed concrete will last more than 50 years.
Read article
Stamped concrete is both a kind of decorative coating and a concrete hardener, with which the surface becomes resistant to mechanical shocks.
Read article
Decorative printed concrete is easy to apply, not picky to use and with its help you can create an imitation of a variety of expensive decorative materials.
Read article
Printed concrete is a kind of decorative coating for external use, with which you can create an imitation of various decorative materials, such as decorative stone, brick, paving slabs and others, while the wear resistance of the concrete surface will also be an order of magnitude higher.
Read article
The hardener for freshly printed concrete Teknoser Baski has quartz fillers and other components in its composition that increase the wear resistance of the surface.
Read article
