Transparent polyurethane-based waterproofing, UV-resistant Teknobond 660
Transparent two-component waterproofing material based on polyurethane, resistant to ultraviolet light.
6936 uah
Product Description
Transparent two-component waterproofing material based on polyurethane, resistant to ultraviolet rays.
Areas of application
- Waterproofing of balconies and terraces.
- Waterproofing of glass brick walls.
- Waterproofing and preservation of natural stone.
- Waterproofing and protection of wood.
- Waterproofing of metal surfaces.
- Use on surfaces that require resistance to ultraviolet rays.
Features and benefits
- Has excellent adhesion to surfaces such as concrete, stone, ceramics, asphalt, steel, wood.
- Can be applied by brush, roller or spray.
- Resistant to ultraviolet rays, heat resistance, abrasion, impact and chemical resistance.
- Easy to apply on horizontal and vertical surfaces.
Application information
Surface quality: the surface must be free from any dust, dirt, loose and volatile particles, cement mortar residues and oils. The concrete surface must have sufficient compressive strength (at least 25 N/mm2), the tear strength must be at least 1.5 N/mm2.
Notes/Limitations
- Do not use at the minimum permissible temperature until the material has completely hardened.
- The product can irritate the skin. Protective gloves and goggles must be worn. Protective hand cream can be applied before starting work. In case of contact with the eyes, rinse them immediately with water and consult a doctor.
- If the material is stored at temperatures below 0°C for a long time, crystallization may occur in the product. If the crystals dissolve by returning the product to room temperature, it can be used further.
- After adding component B, mix component A for 2-3 minutes until a uniform color is obtained using a low-speed mixer (up to 400 rpm).
- Contact with skin may cause irritation. Avoid contact with eyes.
- Equipment used must be cleaned immediately after application. Cured product can only be cleaned mechanically.
| Basic information | |
| Material base | Polyurethane |
| Color | Transparent |
| Packaging | 5 kg set |
| Density | 0.97 ± 00.3 (kg/l) |
| Application information | |
| Drying time |
Foot traffic after 3 days Full drying 7 days |
| Working solution life time | 40 - 45 min |
| Tool cleaning time | 45 min |
| Surface temperature for application | (+5°C) - (+ 30°C) |
| Material consumption | 100-150 g/m² |
Surface preparation
Clean the surface from dirt, dust and grease stains. Particular attention should be paid to the seams.
Mixing the components
Teknobond 660 is a two-component material. Before application, mix both components thoroughly until a homogeneous mixture is obtained using a low-speed mixer.
Application
Apply the material to the surface in an even layer using a roller or brush. For seams, use a narrow brush to ensure complete sealing.
Drying time
Depending on the conditions in which the waterproofing is applied. The material dries within 24–48 hours. After that, the surface is ready for use.
-
Which waterproofing is suitable for indoor and outdoor use without removing the existing finish?
Transparent waterproofing is ideal for such cases, as it can be applied without removing tiles, stone, or other final finishes. For example, Teknobond 660, a two-component polyurethane waterproofing, deeply penetrates microcracks, forms a transparent elastic film, and preserves the appearance of the surface. -
Can I waterproof a bathroom if the tiles are already installed?
Yes, you can! Transparent polyurethane waterproofing like Teknobond 660 is applied directly over the tiles with a brush or roller, without removing them. It creates a thin protective layer that prevents water from seeping into joints and the substrate. -
What is the best waterproofing for a polished concrete terrace floor?
Polished concrete looks modern and is very durable, but when used outdoors, it needs extra protection from water. The waterproofing must resist UV rays, temperature changes, and precipitation. Teknobond 660 is excellent for this purpose — it protects the surface, increases wear resistance, and prevents efflorescence. -
How to avoid removing tiles when a pool leaks?
Instead of expensive tile removal, transparent waterproofing can be applied directly onto the tiled surface. For instance, Teknobond 660 can be used to seal the pool from above, forming a flexible, completely transparent, UV-resistant coating. -
How to protect a bathroom from water leaks, moisture, and mold?
To avoid leaks after renovation, it’s essential to seal pores and microcracks in tiles and joints. This can be done without removing the finish using the right waterproofing. A great solution is Teknobond 660, which forms a transparent vapor-proof film and protects the surface from further damage. -
What waterproofing is suitable for an open wooden terrace?
Wood requires a breathable yet water-resistant coating. Teknobond 660 transparent polyurethane waterproofing forms an elastic UV-resistant protective layer that adapts to wood’s movement and preserves its natural texture and color. -
Is there transparent waterproofing that doesn’t yellow over time?
Yes. For example, Teknobond 660 offers high UV resistance and remains perfectly clear, even after several seasons under the sun. This is especially important for terraces, pools, balconies, and façades. -
Can transparent waterproofing withstand freezing temperatures?
High-quality polyurethane waterproofing like Teknobond 660 can withstand temperatures as low as -30°C without losing its properties. This makes it ideal for both indoor and outdoor use in cold climates. -
Which is better: acrylic or polyurethane transparent waterproofing?
Polyurethane waterproofing like Teknobond 660 generally offers better adhesion, greater elasticity, and a longer service life than acrylic alternatives. It also withstands mechanical stress and UV rays better, making it suitable for more demanding conditions. -
Does transparent waterproofing protect against salt stains and efflorescence?
Yes, Teknobond 660 creates an impermeable barrier that prevents salts from surfacing. It helps preserve the decorative appearance of tile, stone, or concrete, even in damp environments.
