Teknomer 200 EX Crystallized is a two-component elastic penetrating waterproofing compound that consists of a cement-based powder component, a liquid component based on an emulsion polymer and special additives that increase water resistance and protect the surface. It is resistant to positive and negative water pressure.
Application areas:
- For internal and external application
- For horizontal and vertical surfaces
- For terraces, balconies, garages, storerooms and other rooms with high humidity and dampness
- For ground floors and basements, elevator shafts and foundations
Properties of waterproofing:
- Resistant to positive and negative water pressure
- It has a high adhesive strength
- Does not cause corrosion on the fittings
- Prevents carbonation in concrete
- It can be applied to all types of stone surfaces, brick, aerated concrete, concrete and plaster
- Resistant to freezing and thawing
- Easy to use. It can be applied with a brush, roller or spatula.
Composition of the material |
Component 1: grey powder |
Component 2: white liquid |
Expiration date |
12 months in a dry environment in a closed package |
Packaging |
25 + 10 kg |
Application temperature |
+5 °C - +35 °C |
Life time of the compound |
45 minutes |
Expenditure |
1,4 kg/m2 |
Waiting time between layers |
3-6 hours |
Commissioning |
7 days |
Water resistance |
10 Bar (negative), 10 Bar (positive) |
Adhesive strength (EN 1542) |
> 0,80 N/mm2 |
Adhesive strength (EN 14891) |
> 1,0 N/mm2 |
Water vapor penetration (TS EN ISO 7783-2) |
Class 1; Sd |
Crack penetration (EN 1062-7) |
Class A3; 0,5 mm - 1,25 mm |
Capillary absorption of water (EN 13057) |
< 0,1 kg/m2*h |
Thermal stability |
- 40 °C - +80 °C |
Fire resistance |
Vs1d0 |
- Before applying the material, the surface should be cleaned of any types of oil, rust, detergents, dirt and other substances that prevent setting.
- If there are cracks or other damages on the surface, they must be previously repaired with Teknorep repair solutions.
- If there are active leaks, they should be sealed with Teknoplug.
- The material should be applied to a wet surface.
- To prepare the working solution, pour the liquid component (10 liters) in a clean container, then slowly pour out the powdered component (25 kg). Using a low-speed mixer (500 rpm), knead the composition for 5 minutes until a homogeneous mass is obtained. Leave the resulting mixture for 2-3 minutes, then re-mix the compound for 3 minutes.
- The compound should be applied to the surface with a brush or a spatula. Each next layer should be applied perpendicular to the previous one.
- The layer dries for at least 3 hours. If more than 12 hours have passed after applying the layer, moisten the surface before applying the next one.
- The total thickness of the application layers is 3 mm.
- On the surface to be tiled, each corner should be worked out using the Teknomer pah bandi tape.
Notes:
- The average lifetime of the compound is 120 minutes, but in conditions of high temperature, strong wind, low humidity, the lifetime of the compound may decrease.
- After applying the material, it is necessary to protect the surface from direct sunlight for 24 hours.
- After applying the waterproofing make sure that direct sunlight and precipitation do not fall on the surface, and also do not use the material at temperatures above + 35 ˚С and below + 3 ˚С.
- In case of constant pedestrian loads or in case of sunlight, after the waterproofing mixture has completely dried (at least 7 days) it is necessary to apply a finishing coating, for example, ceramic tiles.
- The tools and equipment used must be washed with water immediately after use.
- Work should be carried out in compliance with safety and hygiene standards, using a mask and glasses.
1. Do I need to waterproofing the basement?
Yes. This is especially true of the exterior of the building, since it is from there that the main effect of moisture on concrete occurs.
2. What is needed for waterproofing the foundation?
Waterproofing the foundation can be done in several ways:
1. add a special additive for the waterproofness of Teknomer 120 concrete at the pouring stage;
2. cover the foundation with bitumen, polymer cement or polyurethane waterproofing;
3. use roll waterproofing.
3. How to protect the foundation from moisture?
Reliable protection of the foundation from moisture will be provided by the elastic penetrating waterproofing mixture Teknomer 200 EX Crystallized. The water resistance of which is 10 Bar (for positive and negative water pressure).
4. What is the best waterproofing?
The best waterproofing mixture is the one that is ideally suited specifically to your needs. But there is a fairly universal Teknomer 200 EX Crystallized material – a two-component polymer-cement elastic penetrating waterproofing that protects the bases from positive and negative water pressure.
5. What is waterproofing mastic for?
Waterproofing mastic is used to protect mineral bases from damage that may occur due to exposure to moisture.