Thermoplastic expansion tape 200 (Текномер 200)

Products > Waterproofing materials

Thermoplastic expansion tape 200 (Текномер 200)

Thermoplastic tape for sealing expansion joints, cracks, joints

210
uah
x
m.p.
=
210 uah
CHECKOUT

Введите свои данные

Teknomer thermoplastic tape for sealing expansion joints, cracks, in waterproofing basements, tunnels and other underground structures, pools and various hydraulic structures.
Teknomer thermoplastic tape has perforated edges, 200mm wide and 1mm thick. It is a component of the sealing system with Teknobond 400 D epoxy adhesive.
Application:

  • expansion joints in floors, walls, ceilings
  • expansion joints separating separate sections of buildings
  • cold and working seams
  • joints of prefabricated concrete structures

Features / Benefits

  • the system is resistant to positive and negative pressure
  • Possibility of laying on wet surfaces
  • has high chemical resistance
  • wear resistance
  • does not require mechanical fastening
  • working ambient temperature from -40˚С to +90˚С
  • compatibility with bitumen-based materials
  • resistance to UV radiation

 

Химическая основа Лента на основе термопластического эластомера
Упаковка 25 м рулон
Срок годности 24 месяца
Условия хранения Хранить в сухой среде, в закрытой оригинальной упаковке
Цвет Серый
Ширина 20 см
Толщина 1 мм
Вес 930 гр/м2
Прочность по Шору А 94
Относительное удлинение при разрыве в продольном направлении 1000%
Прочность на разрыв <4 Н/мм2
Относительное удлинение при разрыве в поперечном направлении 1000%
Устойчивость к давлению >4 Бар
Разрывная нагрузка в продольном направлении 14 Н/мм2
Разрывная нагрузка в поперечном направлении 14 Н/мм2
Класс огнестойкости 82
Устойчивость к УФ-излучению >6500 годин
Термостойкость -40°C / +90°C

 

The quality of the base / preliminary preparation

The application surface must be dry and free from any kind of dust, dirt, weak and loose particles, remains of cement mortar, oil and grease. If there are weak concrete parts, they should be removed, after which the surface should be repaired with a high-strength repair solution.

The concrete base must be clean, strong and have sufficient compressive strength (minimum 25 N/mm2) and tensile strength at least 1.5 N/mm2.

Stacking

Before laying the Teknomer tape, it must be cut with scissors or a utility knife according to the length of the compensation seam and wiped with a small amount of solvent.

If necessary, put the tape on top of each other, the length of the overlap should be 10 cm. The tapes are connected to each other with the help of hot air. If desired, a polyethylene wick larger than the expansion width is inserted into the joint.

The expansion tape is glued using special Teknobond 400 D epoxy glue, which is applied with a spatula 5 cm on each side of the tape. Do not apply epoxy to the middle of the tape.

In order for the tape not to lose its elastic properties quickly, it is recommended to lay it by making a straight or inverted omega. The next day, you should re-apply the material to the tape, paying attention to the high-quality finishing of the edges.

Limitation

  • It is not recommended to lay the tape in rainy weather.
  • After laying, the tape must be protected from adverse weather conditions, such as direct sunlight, strong wind, high air temperature (above +35°C), rain and frost.

Product publications

Waterproofing of civil defense protective structures - DBN B.2.2-5:2023
Waterproofing of civil defense protective structures - DBN B.2.2-5:2023

Let's consider paragraph 15 DESIGN OF WATERPROOFING OF DEEP PARTS OF PROTECTIVE STRUCTURES AND SPP

Read article
How to waterproof corners?
How to waterproof corners?

Waterproofing corners in a building is very important as it prevents moisture and water from penetrating through joints and corners of structures

Read article
How to fill the expansion joint between the foundations?
How to fill the expansion joint between the foundations?

To fill the expansion joint between foundations, special sealants or tape materials are usually used, which provide flexibility and the ability to compensate for deformations and movements between adjacent foundations

Read article
How to seal expansion joints in concrete?
How to seal expansion joints in concrete?

Expansion joints in concrete can be sealed with a variety of materials depending on project requirements and the type of joint.

Read article
Do I need to make a deformation seam?
Do I need to make a deformation seam?

Expansion joints are planned gaps in a structure that allow control of deformations caused by thermal or mechanical stresses, and also reduce the likelihood of cracks and damage in concrete or stone.

Read article