Polymer cement waterproofing Teknomer 200 Crystallized (Текномер 200 Кристалайзд)

• Before applying the material, the surface should be cleaned of any types of oil, rust, detergents, dirt and other substances that prevent setting.
• If there are cracks or other damages on the surface, they must be previously repaired with Teknorep repair solutions.
• If there are active leaks, they should be sealed with Teknoplug.
• The material should be applied to a wet surface.
• After applying the material, it is necessary to protect the surface from direct sunlight for 24 hours.
• To prepare the waterproofing compound, pour the liquid component into a clean container and add 5.0 - 6.0 liters of clean water, then slowly pour out the powdered component (25 kg). Using a low-speed mixer, knead the composition until a homogeneous mass is obtained. Leave the resulting compound for 5 minutes, then re-mix the compound for 30 seconds.
• Teknomer 200 Crystallized should be applied to the surface with a brush or spatula in 2-3 layers. Each next layer should be applied perpendicular to the previous one. The layer dries for at least 3 hours. If more than 12 hours have passed after applying the layer, moisten the surface before applying the next one.
• The total thickness of the application layers is 3 mm.
• On the surface that will be laid with tiles, you should work out every corner with the help of Teknomer pah bandi tape.
• When applying waterproofing to the screed, it is necessary to use a waterproofing mesh between the layers.

Notes:

• The average lifetime of the mixture is 120 minutes, but in conditions of high temperature, strong wind, low humidity, the lifetime of the compound may decrease.
• After applying the waterproofing make sure that direct sunlight and precipitation do not fall on the surface, and also do not use the material at temperatures above + 35 ˚С and below + 3 ˚С.
• After 7 days after applying the waterproofing, you can start laying tiles or ceramics or apply plaster or screed.
• The tools and equipment used must be washed with water immediately after use.
• Work should be carried out in compliance with safety and hygiene standards, using a mask and glasses.

1. How to treat concrete from water?

Water is one of the most dangerous destroyers of concrete, so it must be treated with special waterproofing mixtures to protect against moisture. Teknomer 200 Crystallized material is considered a good option.

2. What is better to use for waterproofing?

There is no universal material for waterproofing. It needs to be selected taking into account all the nuances of operation, surface features and location of the object that needs to be protected from moisture. If it is necessary to use a coating waterproofing, we recommend paying attention to the Teknomer 200 Crystallized material.

3. What are the methods of applying coating waterproofing materials?

There are 3 ways to apply coating waterproofing materials: by brush, roller or mechanical spray. The difference between these methods may be in the speed of application of the material and its consumption. 

4. What to use for waterproofing the floor?

Both for waterproofing the walls and for waterproofing the floor, a high-quality, proven waterproofing material is needed. Teknomer 200 Crystallized will give stability to horizontal and vertical surfaces to positive and negative water pressure.

5. How to do waterproofing in the bathroom?

The bathroom is a room with constantly high humidity. Therefore, it is necessary to take a very responsible approach to the choice of waterproofing material and the master. Before waterproofing, you can apply a primer or moisten the surface well. 

6. How to protect the basement from groundwater?

To protect the basement from groundwater, it is necessary to choose a waterproofing that is resistant to the negative effects of water. 7 days after applying Teknomer 200 Crystallized, the basement will be reliably protected from moisture. 

7. How to waterproofing brickwork?

For waterproofing brickwork, a polymer-cement waterproofing mixture, the total thickness of which is 3 mm, is best suited. 

8. How to make waterproofing of an external wall?

Waterproofing of external walls can be both penetrating and coating material. And it is better to use the penetrating coating waterproofing Teknomer 200 Crystallized and reliably isolate the surface from the penetration of moisture from the outside.